ユニバーサル・シートクッション

全モデル

詳細を見る

ユニバーサル・シートクッション

品番 S230
EUR 91,90
税込, 送料別
USD: $101.02GBP: £76.81AUD: A$150.51JPY: ¥16,160
納期: 即納可能

このユニバーサル・シートクッションは、背中と臀部の負担を軽減することで、乗り心地を向上させ、よりリラックスして快適な乗り心地を実現します。柔らかく膨らませるTPUインナーパッドは、通気性のある黒い生地で覆われており、最適な座り心地を提供します。2つの一体型バルブのおかげで、空気圧を個別に調整して、個人の好みに応じて座り心地を最適化できます。

バイクのサドルの下を通る2本のストラップは、CAMフックで固定され、しっかりと固定されます。滑り止めの裏面により、サドルを安定して保持します。クッションは、体重130kgまでのライダーに適しています。この実用的なアクセサリーは、長距離のバイクツーリングをさらに快適にします。

長さ:約38cm
背面の幅:約35cm
前面の幅:約15cm

商品についての質問

レビュー


未レビューの商品はありません



関連・おすすめ商品

スクリーン・スポイラー
スクリーン・スポイラー

BMW R1200GS & R1200GS Adventure モデル

MRA X-creen スポイラーは、 厄介な乱気流・風圧・風切り音を軽減するために、個々のライダーの、その時のニーズに応えてくれます。このスポイラーは、角度調整可能な2つの独立したピボット部分にて支持します。スポイラーの幅は36cm、高さは16.3cmです。色は、クリアとスモークグレイからお選びください。EU の認証に適合しています。 ノーマルのスクリーン、及び、MRAのスクリーンでお使いいただけます。このスポイラーは、ネジで固定、または別売りのクランプで固定することができます。 ネジで固定の場合:X-creenスポイラーを4つのネジで固定します。取り付けるスクリーンの適切な位置に、固定のための穴を開ける必要があります。ネジ穴の左右の間隔は、25cmです。 クランプで固定の場合:X-creenスポイラーを、専用のクランプで固定します。写真3をご参照下さい。この方法では、穴あけや接着剤は必要ありません。このクランプは、X-creenスポイラーには付属していませんので、別途、ご購入下さい。クランプで固定する場合には、スクリーンの上部の幅が、28cm以上必要です。 クランプ (4025066125074) を使用する場合、このスポイラーは、R1200GS 2004-2012 のノーマルスクリーンにのみ、取り付けが可能です。 MRA X-creen 認証適合書(ドイツ語)

EUR 79,90EUR 89.90

税込, 送料別

詳細を見る
Examples for seat conversion
Examples for seat conversion

By default, we use non-slip black synthetic leather and black stitching for the seat conversion. However, it is also possible to customize the appearance of the seat at an additional cost. Optional seat conversion options: - other type of synthetic leather - another leather color - stitching - paint letters or numbers on the seat, for example "XR" - different colored seams Prices and other example images can be found here: Examples for seat conversion Please let us know by email which extras you would like for your seat conversion. We will then check whether the seat conversion is possible as desired and inform you of the total price.

詳細を見る
シートヒーターの後付け
シートヒーターの後付け

通関手数料が発生するため、EU以外の国からのシートの発送をお受けすることができません。大変申し訳ありませんが、EU域外からシートを発送するお客様には、「シートヒーターの後付け」サービスをご提供することができません。 Retrofitting a 2-stage (15W/30W) seat heater for seats that do not have seat heating as standard. Possible either only in the rider's position or in the rider's and passenger's position. The original seat cover must be removed for installation, which is why it must not be glued to the foam core! Check whether the cover can be lifted off the foam core! To do this, pinch the cover between your thumb and forefinger and try to lift it (see figure 4). Attention: If the cover is glued, the seat heating can only be retrofitted in combination with a seat conversion (see seat conversion (one-piece seat) / seat conversion (two-piece seat))! After installing a seat heater, the cable for the power supply is led out under the seat shell (approx. 20 cm long with plug connection). You will receive an approx. 120cm long connection cable with a two-stage, round built-in toggle switch (diameter approx. 20mm) for each heated seat position. The connection to the electrical system of your motorcycle should be carried out by a specialist workshop, knowledge of motorcycle electronics is required! A circuit diagram is included. The seat heater will be installed on your seat - you have to send it in! The change takes about 2-3 weeks. The illustration of the lead-through of the connection cable is an example. The location of the grommet may vary depending on the seat and model.

EUR 216,75EUR 255.00

税込, 送料別

詳細を見る