Seat conversion for BMW R1250GS & R1250GS Adventure

8件の商品

フロントシート、リアシートの改良
フロントシート、リアシートの改良

通関手数料が発生するため、EU 以外の国からのシートの発送をお受けすることができません。大変申し訳ありませんが、EU外からシートを発送するお客様には、「シートの改良」サービスをご提供することができません。 The seat is modified according to your individual needs. Based on your information on our seat data sheet, we can adapt the seat to you in terms of hardness, contour and height. Among other things, a groove (deepened middle of the seat) is possible, which noticeably relieves the coccyx if there are problems with it. The seat conversion is possible with different height options: 1: like the original seat 2: lower (up to -25mm) 3: higher (up to +25mm) BMW R1250GS is also available with factory seat heating. This results in the following restrictions: Lowering the seat (-25 mm) is not possible due to the heating integrated in the seat. When making the seat higher (+25mm), the additional foam reduces the heat output. Many seats are also offered by BMW in a low version - these cannot be lowered further. By default we use non-slip black synthetic leather and black stitching for the seat conversion (other colors are also possible). Several colors or different types of imitation leather, lettering and other customizations are possible at an additional cost. Example modifications: Examples of seat modifications Please fill out the seat change form and send it to us. Please wait for our confirmation before sending the seat to us. In this way you can avoid unnecessary shipping costs if a conversion cannot be carried out as desired. Your data sheet: Please fill in and send to us! Your seat will be modified - it must be sent in! The modification will take about 2 weeks. Each image of the service "seat conversion" can of course only be an example! Seams are not always possible with very soft seats, for example! Our upholsterer can only decide whether a seam needs to be incorporated or not after he has received the information on your form. If there is no seat heating as standard, an accessory seat heating can be retrofitted with the seat conversion. The retrofit includes the installation of a 2-stage (15W/30W) seat heater and all connection parts required for operation. After installing a seat heater, the cable for the power supply is led out under the seat shell (approx. 20 cm long with plug connection). You will receive an approx. 120cm long connection cable with a two-stage, round built-in toggle switch (diameter approx. 20mm) for each heated seat position. The connection to the electrical system of your motorcycle should be carried out by a specialist workshop, knowledge of motorcycle electronics is required! A circuit diagram is included. The illustration of the lead-through of the connection cable is an example. The location of the grommet may vary depending on the seat and model. We assume no guarantee for a seat heater is already installed. If the seat heating worked before the seat conversion, it will also work after the seat conversion.

EUR 229,00EUR 240.00

税込, 送料別

詳細を見る
シートカバー AIR
シートカバー AIR

このシートカバー「AIR」は、シート周囲の空気循環を一定に保ちます。走行中はメッシュ生地を通して空気が循環し、シートを効果的に冷却します。また、炎天下の駐車時にシートが過熱するのを軽減します。マジックテープで簡単にシートに取り付けることができます。3Dメッシュ生地製。 前席シート用と後席用シートのセットです。

EUR 84,90EUR 94.90

税込, 送料別

詳細を見る
ワンピースシートの改良
ワンピースシートの改良

通関手数料が発生するため、EU 以外の国からのシートの発送をお受けすることができません。大変申し訳ありませんが、EU外からシートを発送するお客様には、「シートの改良」サービスをご提供することができません。 The seat is modified according to your individual needs. Based on your information on our seat data sheet, we can adapt the seat to you in terms of hardness, contour and height. Among other things, a groove (deepened middle of the seat) is possible, which noticeably relieves the coccyx if there are problems with it. The seat conversion is possible with different height options: 1: like the original seat 2: lower (up to -25mm) 3: higher (up to +25mm) BMW R1250GS is also available with factory seat heating. This results in the following restrictions: Lowering the seat (-25 mm) is not possible due to the heating integrated in the seat. When making the seat higher (+25mm), the additional foam reduces the heat output. Many seats are also offered by BMW in a low version - these cannot be lowered further. By default we use non-slip black synthetic leather and black stitching for the seat conversion (other colors are also possible). Several colors or different types of imitation leather, lettering and other customizations are possible at an additional cost. Example modifications: Examples of seat modifications Please fill out the seat change form and send it to us. Please wait for our confirmation before sending the seat to us. In this way you can avoid unnecessary shipping costs if a conversion cannot be carried out as desired. Your data sheet: Please fill in and send to us! Your seat will be modified - it must be sent in! The modification will take about 2 weeks. Each image of the service "seat conversion" can of course only be an example! Seams are not always possible with very soft seats, for example! Our upholsterer can only decide whether a seam needs to be incorporated or not after he has received the information on your form. If there is no seat heating as standard, an accessory seat heating can be retrofitted with the seat conversion. The retrofit includes the installation of a 2-stage (15W/30W) seat heater and all connection parts required for operation. After installing a seat heater, the cable for the power supply is led out under the seat shell (approx. 20 cm long with plug connection). You will receive an approx. 120cm long connection cable with a two-stage, round built-in toggle switch (diameter approx. 20mm) for each heated seat position. The connection to the electrical system of your motorcycle should be carried out by a specialist workshop, knowledge of motorcycle electronics is required! A circuit diagram is included. The illustration of the lead-through of the connection cable is an example. The location of the grommet may vary depending on the seat and model. We assume no guarantee for a seat heater is already installed. If the seat heating worked before the seat conversion, it will also work after the seat conversion.

EUR 279,65EUR 329.00

税込, 送料別

詳細を見る
シートヒーターの後付け
シートヒーターの後付け

通関手数料が発生するため、EU以外の国からのシートの発送をお受けすることができません。大変申し訳ありませんが、EU域外からシートを発送するお客様には、「シートヒーターの後付け」サービスをご提供することができません。 Retrofitting a 2-stage (15W/30W) seat heater for seats that do not have seat heating as standard. Possible either only in the rider's position or in the rider's and passenger's position. The original seat cover must be removed for installation, which is why it must not be glued to the foam core! Check whether the cover can be lifted off the foam core! To do this, pinch the cover between your thumb and forefinger and try to lift it (see figure 4). Attention: If the cover is glued, the seat heating can only be retrofitted in combination with a seat conversion (see seat conversion (one-piece seat) / seat conversion (two-piece seat))! After installing a seat heater, the cable for the power supply is led out under the seat shell (approx. 20 cm long with plug connection). You will receive an approx. 120cm long connection cable with a two-stage, round built-in toggle switch (diameter approx. 20mm) for each heated seat position. The connection to the electrical system of your motorcycle should be carried out by a specialist workshop, knowledge of motorcycle electronics is required! A circuit diagram is included. The seat heater will be installed on your seat - you have to send it in! The change takes about 2-3 weeks. The illustration of the lead-through of the connection cable is an example. The location of the grommet may vary depending on the seat and model.

EUR 216,75EUR 255.00

税込, 送料別

詳細を見る
Examples for seat conversion
Examples for seat conversion

By default, we use non-slip black synthetic leather and black stitching for the seat conversion. However, it is also possible to customize the appearance of the seat at an additional cost. Optional seat conversion options: - other type of synthetic leather - another leather color - stitching - paint letters or numbers on the seat, for example "XR" - different colored seams Prices and other example images can be found here: Examples for seat conversion Please let us know by email which extras you would like for your seat conversion. We will then check whether the seat conversion is possible as desired and inform you of the total price.

詳細を見る
New cover for seat
New cover for seat

通関手数料のため、EU 以外の国からの座席の提出は受け付けられません。 したがって、EU 圏外から座席を送付する必要がある場合は、残念ながら「座席の新しいカバー」というサービスを提供できません。. If your seat cover is damaged or worn, we can equip your seat with a new cover. For example, if you have your rider's seat reupholstered by us, it can also make sense for visual reasons to have the passenger seat covered with the same artificial leather so that the overall result looks harmonious. By default, we use non-slip black synthetic leather and black stitching for the seat cover (other colors are also possible). Several colors or different types of synthetic leather, lettering and other customizations are possible at an additional cost. The original seat cover must be removed, which is why it must not be glued to the foam core! Check whether the cover can be lifted off the foam core! To do this, pinch the cover between your thumb and forefinger and try to lift it (see figure 2). Attention: If the cover is glued, a new seat cover can only be realized as part of a seat conversion (see seat conversion (one-piece seat) / seat conversion (two-piece seat))! Your seat will be changed - it must be sent in! The change takes about 2 weeks. The illustrations of the service "new cover for seat" are examples! Whether a seam has to be worked in or not depends on the condition of the seat. Our upholsterer will make the new cover similar to the original cover as far as possible.

EUR 126,00EUR 140.00

税込, 送料別

詳細を見る
ユニバーサル・シートクッション
ユニバーサル・シートクッション

このユニバーサル・シートクッションは、背中と臀部の負担を軽減することで、乗り心地を向上させ、よりリラックスして快適な乗り心地を実現します。柔らかく膨らませるTPUインナーパッドは、通気性のある黒い生地で覆われており、最適な座り心地を提供します。2つの一体型バルブのおかげで、空気圧を個別に調整して、個人の好みに応じて座り心地を最適化できます。 バイクのサドルの下を通る2本のストラップは、CAMフックで固定され、しっかりと固定されます。滑り止めの裏面により、サドルを安定して保持します。クッションは、体重130kgまでのライダーに適しています。この実用的なアクセサリーは、長距離のバイクツーリングをさらに快適にします。 長さ:約38cm 背面の幅:約35cm 前面の幅:約15cm

EUR 91,90

税込, 送料別

詳細を見る
10 mmローダウン用ゴムバッファー
10 mmローダウン用ゴムバッファー

BMW R1250GS モデル

純正シート下のラバーバッファーを交換することで、シート高を約10mm下げることができます。ラバーバッファーは工具を使わず簡単に交換できます。ラバーバッファーの穴はオフセットされています。シートを下げるには、薄い側を上向きにして取り付けてください(画像2参照)。

EUR 14,90

税込, 送料別

詳細を見る

BMW R1250に関する詳細情報

BMW R1250GS または R1250GS Adventure 用のカスタマイズされたシート変換により、長距離ツーリング、日常使用、オフロード使用のいずれの場合でも、乗り心地が著しく向上します。

フォームコアとカバーを、厚さ、輪郭、高さなど、お客様の個人的な仕様に合わせて調整します。例えば B. 尾骨への圧力を大幅に軽減する中空溝付き。変換は元のシートシェルに対してのみ実行されます。シェル自体を変更することはできません。シートがワンピースかツーピースかに関係なく、そのままの状態になります。

🌍 注意: 税関規制により、EU 以外の国からのシートの発送はできません。残念ながら、スイスのお客様は座席変更をご利用いただけません。変換は EU 内でのみ行われます。

3 つの高さのバリエーションから選択できます。

  • 標準の高さ (元のシートの高さ)
  • 下げる: 最大 -25 mm (標準シートヒーターまたはすでに低いバージョンでは不可能)
  • 上げる: 最大 +25 mm (シートヒーターを使用すると、ヒーターの出力が低下する場合があります)

– シート データ シートの仕様 (硬度、輪郭、シートの高さ) に従って調整します。

標準カバーは、黒の装飾ステッチが入った、耐久性のある滑り止め付きの黒の合成皮革で作られています。リクエストに応じて、他の色のバリエーション、人工皮革の種類、または対照的な縫い目が可能で、個別の文字(例:「GS」)も使用できます。

アクセサリーの後付け: 標準でシートヒーターが装備されていないシートには、オプションでシートヒーター(15W/30W)を統合できます。これには、接続ケーブル(約120cm)、トグルスイッチ(約20mm)、配線図が含まれます。接続は専門のワークショップで行う必要があります。

🔄 プロセスとサービス:
1. シート変更フォームに記入して送信してください。お客様のご希望が実現可能かどうかを確認いたします。
2. 確認後、シートをお送りください。提出が必要です。
3. 変換時間は通常約 2 週間です。

🤝 結論: 当社のシート変換サービスを使用すると、人間工学に基づいた形状、より柔らかく、より硬く、高く、または低く、快適さ、デザイン、機能がお客様の BMW R1250GS または R1250GS Adventure に合わせてカスタマイズできます。

今すぐカスタマイズされたシート変換を注文して、あらゆるルートで究極の乗り心地を実現しましょう。