Seat conversion for BMW R850GS, BMW R1100GS, BMW R1150GS & BMW R1150GS Adventure

6件の商品

ワンピースシートの改良
ワンピースシートの改良

BMW R1150GS Adventure モデル

通関手数料が発生するため、EU 以外の国からのシートの発送をお受けすることができません。大変申し訳ありませんが、EU外からシートを発送するお客様には、「シートの改良」サービスをご提供することができません。 The seat is modified according to your individual needs. Based on your information on our seat data sheet, we can adapt the seat to you in terms of hardness, contour and height. Among other things, a groove (deepened middle of the seat) is possible, which noticeably relieves the coccyx if there are problems with it. The seat conversion is possible with different height options: 1: like the original seat 2: lower (up to -25mm) 3: higher (up to +25mm) Many seats are also offered by BMW in a low version - these cannot be lowered further. By default we use non-slip black synthetic leather and black stitching for the seat conversion (other colors are also possible). Several colors or different types of imitation leather, lettering and other customizations are possible at an additional cost. Example modifications: Examples of seat modifications Please fill out the seat change form and send it to us. Please wait for our confirmation before sending the seat to us. In this way you can avoid unnecessary shipping costs if a conversion cannot be carried out as desired. Your data sheet: Please fill in and send to us! Your seat will be modified - it must be sent in! The modification will take about 2 weeks. Each image of the service "seat conversion" can of course only be an example! Seams are not always possible with very soft seats, for example! Our upholsterer can only decide whether a seam needs to be incorporated or not after he has received the information on your form. If there is no seat heating as standard, an accessory seat heating can be retrofitted with the seat conversion. The retrofit includes the installation of a 2-stage (15W/30W) seat heater and all connection parts required for operation. After installing a seat heater, the cable for the power supply is led out under the seat shell (approx. 20 cm long with plug connection). You will receive an approx. 120cm long connection cable with a two-stage, round built-in toggle switch (diameter approx. 20mm) for each heated seat position. The connection to the electrical system of your motorcycle should be carried out by a specialist workshop, knowledge of motorcycle electronics is required! A circuit diagram is included. The illustration of the lead-through of the connection cable is an example. The location of the grommet may vary depending on the seat and model. We assume no guarantee for a seat heater is already installed. If the seat heating worked before the seat conversion, it will also work after the seat conversion.

EUR 279,65EUR 329.00

税込, 送料別

詳細を見る
フロントシート、リアシートの改良
フロントシート、リアシートの改良

BMW R850GS, R1100GS & R1150GS モデル

通関手数料が発生するため、EU 以外の国からのシートの発送をお受けすることができません。大変申し訳ありませんが、EU外からシートを発送するお客様には、「シートの改良」サービスをご提供することができません。 The seat is modified according to your individual needs. Based on your information on our seat data sheet, we can adapt the seat to you in terms of hardness, contour and height. Among other things, a groove (deepened middle of the seat) is possible, which noticeably relieves the coccyx if there are problems with it. The seat conversion is possible with different height options: 1: like the original seat 2: lower (up to -25mm) 3: higher (up to +25mm) Many seats are also offered by BMW in a low version - these cannot be lowered further. By default we use non-slip black synthetic leather and black stitching for the seat conversion (other colors are also possible). Several colors or different types of imitation leather, lettering and other customizations are possible at an additional cost. Example modifications: Examples of seat modifications Please fill out the seat change form and send it to us. Please wait for our confirmation before sending the seat to us. In this way you can avoid unnecessary shipping costs if a conversion cannot be carried out as desired. Your data sheet: Please fill in and send to us! Your seat will be modified - it must be sent in! The modification will take about 2 weeks. Each image of the service "seat conversion" can of course only be an example! Seams are not always possible with very soft seats, for example! Our upholsterer can only decide whether a seam needs to be incorporated or not after he has received the information on your form. If there is no seat heating as standard, an accessory seat heating can be retrofitted with the seat conversion. The retrofit includes the installation of a 2-stage (15W/30W) seat heater and all connection parts required for operation. After installing a seat heater, the cable for the power supply is led out under the seat shell (approx. 20 cm long with plug connection). You will receive an approx. 120cm long connection cable with a two-stage, round built-in toggle switch (diameter approx. 20mm) for each heated seat position. The connection to the electrical system of your motorcycle should be carried out by a specialist workshop, knowledge of motorcycle electronics is required! A circuit diagram is included. The illustration of the lead-through of the connection cable is an example. The location of the grommet may vary depending on the seat and model. We assume no guarantee for a seat heater is already installed. If the seat heating worked before the seat conversion, it will also work after the seat conversion.

EUR 229,00EUR 240.00

税込, 送料別

詳細を見る
シートヒーターの後付け
シートヒーターの後付け

通関手数料が発生するため、EU以外の国からのシートの発送をお受けすることができません。大変申し訳ありませんが、EU域外からシートを発送するお客様には、「シートヒーターの後付け」サービスをご提供することができません。 Retrofitting a 2-stage (15W/30W) seat heater for seats that do not have seat heating as standard. Possible either only in the rider's position or in the rider's and passenger's position. The original seat cover must be removed for installation, which is why it must not be glued to the foam core! Check whether the cover can be lifted off the foam core! To do this, pinch the cover between your thumb and forefinger and try to lift it (see figure 4). Attention: If the cover is glued, the seat heating can only be retrofitted in combination with a seat conversion (see seat conversion (one-piece seat) / seat conversion (two-piece seat))! After installing a seat heater, the cable for the power supply is led out under the seat shell (approx. 20 cm long with plug connection). You will receive an approx. 120cm long connection cable with a two-stage, round built-in toggle switch (diameter approx. 20mm) for each heated seat position. The connection to the electrical system of your motorcycle should be carried out by a specialist workshop, knowledge of motorcycle electronics is required! A circuit diagram is included. The seat heater will be installed on your seat - you have to send it in! The change takes about 2-3 weeks. The illustration of the lead-through of the connection cable is an example. The location of the grommet may vary depending on the seat and model.

EUR 216,75EUR 255.00

税込, 送料別

詳細を見る
Examples for seat conversion
Examples for seat conversion

By default, we use non-slip black synthetic leather and black stitching for the seat conversion. However, it is also possible to customize the appearance of the seat at an additional cost. Optional seat conversion options: - other type of synthetic leather - another leather color - stitching - paint letters or numbers on the seat, for example "XR" - different colored seams Prices and other example images can be found here: Examples for seat conversion Please let us know by email which extras you would like for your seat conversion. We will then check whether the seat conversion is possible as desired and inform you of the total price.

詳細を見る
New cover for seat
New cover for seat

通関手数料のため、EU 以外の国からの座席の提出は受け付けられません。 したがって、EU 圏外から座席を送付する必要がある場合は、残念ながら「座席の新しいカバー」というサービスを提供できません。. If your seat cover is damaged or worn, we can equip your seat with a new cover. For example, if you have your rider's seat reupholstered by us, it can also make sense for visual reasons to have the passenger seat covered with the same artificial leather so that the overall result looks harmonious. By default, we use non-slip black synthetic leather and black stitching for the seat cover (other colors are also possible). Several colors or different types of synthetic leather, lettering and other customizations are possible at an additional cost. The original seat cover must be removed, which is why it must not be glued to the foam core! Check whether the cover can be lifted off the foam core! To do this, pinch the cover between your thumb and forefinger and try to lift it (see figure 2). Attention: If the cover is glued, a new seat cover can only be realized as part of a seat conversion (see seat conversion (one-piece seat) / seat conversion (two-piece seat))! Your seat will be changed - it must be sent in! The change takes about 2 weeks. The illustrations of the service "new cover for seat" are examples! Whether a seam has to be worked in or not depends on the condition of the seat. Our upholsterer will make the new cover similar to the original cover as far as possible.

EUR 126,00EUR 140.00

税込, 送料別

詳細を見る
ユニバーサル・シートクッション
ユニバーサル・シートクッション

このユニバーサル・シートクッションは、背中と臀部の負担を軽減することで、乗り心地を向上させ、よりリラックスして快適な乗り心地を実現します。柔らかく膨らませるTPUインナーパッドは、通気性のある黒い生地で覆われており、最適な座り心地を提供します。2つの一体型バルブのおかげで、空気圧を個別に調整して、個人の好みに応じて座り心地を最適化できます。 バイクのサドルの下を通る2本のストラップは、CAMフックで固定され、しっかりと固定されます。滑り止めの裏面により、サドルを安定して保持します。クッションは、体重130kgまでのライダーに適しています。この実用的なアクセサリーは、長距離のバイクツーリングをさらに快適にします。 長さ:約38cm 背面の幅:約35cm 前面の幅:約15cm

EUR 91,90

税込, 送料別

詳細を見る

BMW R1100GS1994-1999, BMW R1150GS1999-2004, BMW R1150GS、BMW R850GS1998-2001に関する詳細情報

シート改造 — あなたの BMW R850GS、R1100GS、R1150GS、および R1150GS Adventure のために

BMW R850GS、R1100GS、R1150GS、そして R1150GS Adventure は、多用途性、オフロード性能、そして長距離ツーリングでの耐久性を象徴するモデルです。しかし、多くの純正シートは人間工学的に理想的な形状や、個々の快適性のニーズを十分に満たしていません。Hornig での的確なシート改造により、明確な改善が得られます。クッション材、輪郭、シート高を最適化し、必要に応じてシートの幅も調整することで、快適さと安定性を完璧に両立させます。

 

BMW R850GS、R1100GS、R1150GS、および R1150GS Adventure のための改造サービス

  • クッションおよび形状の調整 – フォーム材を再加工して圧力分布を最適化し、より快適な座面を実現します。
  • 張替え/カスタマイズ – 高品質で耐候性のあるカバー素材を使用。オプションでカラ―アクセント、ロゴ刺繍、または素材の変更も可能です。
  • シートヒーターの後付け – 寒冷時の快適性を高める2段階の加熱機能を追加できます。
  • 幅の調整 – あなたの体型に合わせて、シートをより広く、または狭く成形します。
  • ユニバーサルコンフォートクッション – フル改造を行わずに、すぐに快適性を高めたい場合の簡単な追加ソリューションです。

 

誰がシート改造の恩恵を受けるのか?

BMW R850GS、R1100GS、R1150GS、および R1150GS Adventure のライダーで、長距離ツーリングを頻繁に行う方や、多くの距離を走る方、荷重条件が変わる方には特におすすめです。希望するシートの高さ、幅、またはクッションの硬さが純正状態と異なる場合、あなたの希望に合わせてシートを個別に調整します。疲労軽減、操作性向上、そしてより大きな走行の楽しさを実現します。

 

どのような調整が可能ですか?

  • クッションの硬さと構造:快適で柔らかい仕様からスポーティーで硬めの仕様まで、お好みに合わせて調整します。
  • シートの高さ:わずかに低く、または高くして、地面との接触やライディングポジションを最適化します。
  • 輪郭とサイドサポート:サイドボルスターや溝、段差を追加し、ホールド性と動きやすさを改善します。
  • 幅の変更:体型やライディングスタイルに応じて、座面を広くまたは狭くします。
  • カバーデザインと外観:素材、色のアクセント、コントラストステッチ、またはオリジナルロゴの選択が可能 — スタイルと見た目を自由に決められます。

 

工程:Hornig でのシート改造の流れ

  1. 希望する改造タイプを選択します:クッション調整、張替え、ヒーター追加、幅変更、またはそれらの組み合わせ。
  2. 硬さ、高さ、幅、輪郭に関する詳細をオンラインフォームに記入します。
  3. シートをお送りください。Hornig が加工、品質管理、発送および返送まで責任を持って行います。

 

素材と仕上がり

当社では、耐久性、防水性、滑り止め性に優れたカバー素材と、形状を保つ高品質フォームを使用しています。ご希望に応じて、コントラストステッチ、カラーアクセント、またはオリジナル刺繍を加えた洗練されたデザインを実現します。これにより、BMW R850GS、R1100GS、R1150GS、または R1150GS Adventure は、人間工学的にだけでなく、見た目の面でもさらに魅力的になります。

 

技術的な注意点と作業期間

シート構造(例:接着カバー、一体型ヒーターなど)によって作業内容は異なります。通常、発送と返送を含めて約2~3週間の作業期間を要します。特別なご要望や複雑な改造は個別にご相談させていただきます。

 

シート改造後のメリット

  • 長距離走行でも快適性が向上し、疲労が大幅に軽減されます。
  • 高さ、輪郭、そして幅の個別調整による最適なエルゴノミクス。
  • 側面サポートと輪郭の最適化により、コーナリング時のコントロール性能が向上。
  • プロフェッショナルな張替えによる外観の向上と価値の維持。

 

FAQ – よくある質問

元のシートを送る必要がありますか?

はい。改造、張替え、ヒーター追加、または幅の調整を行うには、既存のシートをお送りいただく必要があります。正確な寸法と形状を反映させるためです。

 

発送と返送にはどのくらいの時間がかかりますか?

通常、発送と返送を含めた全工程で約2~3週間かかります。特別な改造の場合は期間が異なる場合があります。

 

シートを広くまたは狭くすることはできますか?

はい。お客様の体型やライディングスタイルに合わせた幅の調整が可能です。

 

Hornig に相談や詳細を問い合わせるには?

お問い合わせフォームまたは注文フォームをご利用いただき、BMW R850GS、R1100GS、R1150GS、または R1150GS Adventure のシートに関するご希望をお知らせください。喜んでご案内いたします。