ワンピースシートの改良
全モデル

ワンピースシートブラックを変更する
Change one-piece seat black, with installation of seat heating for rider
The seat is modified according to your individual needs. Based on your information on our seat data sheet, we can adapt the seat to you in terms of hardness, contour and height. Among other things, a groove (deepened middle of the seat) is possible, which noticeably relieves the coccyx if there are problems with it.
The seat conversion is possible with different height options:
1: like the original seat
2: lower (up to -25mm)
3: higher (up to +25mm)
BMW R1250GS is also available with factory seat heating. This results in the following restrictions: Lowering the seat (-25 mm) is not possible due to the heating integrated in the seat. When making the seat higher (+25mm), the additional foam reduces the heat output.
Many seats are also offered by BMW in a low version - these cannot be lowered further.
By default we use non-slip black synthetic leather and black stitching for the seat conversion (other colors are also possible). Several colors or different types of imitation leather, lettering and other customizations are possible at an additional cost.
Example modifications: Examples of seat modifications
Please fill out the seat change form and send it to us. Please wait for our confirmation before sending the seat to us. In this way you can avoid unnecessary shipping costs if a conversion cannot be carried out as desired.
Your data sheet: Please fill in and send to us!
Your seat will be modified - it must be sent in!
The modification will take about 2 weeks.
Each image of the service "seat conversion" can of course only be an example! Seams are not always possible with very soft seats, for example! Our upholsterer can only decide whether a seam needs to be incorporated or not after he has received the information on your form.
If there is no seat heating as standard, an accessory seat heating can be retrofitted with the seat conversion.
The retrofit includes the installation of a 2-stage (15W/30W) seat heater and all connection parts required for operation.
After installing a seat heater, the cable for the power supply is led out under the seat shell (approx. 20 cm long with plug connection). You will receive an approx. 120cm long connection cable with a two-stage, round built-in toggle switch (diameter approx. 20mm) for each heated seat position. The connection to the electrical system of your motorcycle should be carried out by a specialist workshop, knowledge of motorcycle electronics is required! A circuit diagram is included.
The illustration of the lead-through of the connection cable is an example. The location of the grommet may vary depending on the seat and model.
We assume no guarantee for a seat heater is already installed. If the seat heating worked before the seat conversion, it will also work after the seat conversion.
商品についての質問
レビュー
未レビューの商品はありません
製品安全情報
関連・おすすめ商品

通関手数料のため、EU 以外の国からの座席の提出は受け付けられません。 したがって、EU 圏外から座席を送付する必要がある場合は、残念ながら「座席の新しいカバー」というサービスを提供できません。. If your seat cover is damaged or worn, we can equip your seat with a new cover. For example, if you have your rider's seat reupholstered by us, it can also make sense for visual reasons to have the passenger seat covered with the same artificial leather so that the overall result looks harmonious. By default, we use non-slip black synthetic leather and black stitching for the seat cover (other colors are also possible). Several colors or different types of synthetic leather, lettering and other customizations are possible at an additional cost. The original seat cover must be removed, which is why it must not be glued to the foam core! Check whether the cover can be lifted off the foam core! To do this, pinch the cover between your thumb and forefinger and try to lift it (see figure 2). Attention: If the cover is glued, a new seat cover can only be realized as part of a seat conversion (see seat conversion (one-piece seat) / seat conversion (two-piece seat))! Your seat will be changed - it must be sent in! The change takes about 2 weeks. The illustrations of the service "new cover for seat" are examples! Whether a seam has to be worked in or not depends on the condition of the seat. Our upholsterer will make the new cover similar to the original cover as far as possible.
詳細を見る
通関手数料が発生するため、EU 以外の国からのシートの発送をお受けすることができません。大変申し訳ありませんが、EU外からシートを発送するお客様には、「シートの改良」サービスをご提供することができません。 The seat is modified according to your individual needs. Based on your information on our seat data sheet, we can adapt the seat to you in terms of hardness, contour and height. Among other things, a groove (deepened middle of the seat) is possible, which noticeably relieves the coccyx if there are problems with it. The seat conversion is possible with different height options: 1: like the original seat 2: lower (up to -25mm) 3: higher (up to +25mm) BMW R1250GS is also available with factory seat heating. This results in the following restrictions: Lowering the seat (-25 mm) is not possible due to the heating integrated in the seat. When making the seat higher (+25mm), the additional foam reduces the heat output. Many seats are also offered by BMW in a low version - these cannot be lowered further. By default we use non-slip black synthetic leather and black stitching for the seat conversion (other colors are also possible). Several colors or different types of imitation leather, lettering and other customizations are possible at an additional cost. Example modifications: Examples of seat modifications Please fill out the seat change form and send it to us. Please wait for our confirmation before sending the seat to us. In this way you can avoid unnecessary shipping costs if a conversion cannot be carried out as desired. Your data sheet: Please fill in and send to us! Your seat will be modified - it must be sent in! The modification will take about 2 weeks. Each image of the service "seat conversion" can of course only be an example! Seams are not always possible with very soft seats, for example! Our upholsterer can only decide whether a seam needs to be incorporated or not after he has received the information on your form. If there is no seat heating as standard, an accessory seat heating can be retrofitted with the seat conversion. The retrofit includes the installation of a 2-stage (15W/30W) seat heater and all connection parts required for operation. After installing a seat heater, the cable for the power supply is led out under the seat shell (approx. 20 cm long with plug connection). You will receive an approx. 120cm long connection cable with a two-stage, round built-in toggle switch (diameter approx. 20mm) for each heated seat position. The connection to the electrical system of your motorcycle should be carried out by a specialist workshop, knowledge of motorcycle electronics is required! A circuit diagram is included. The illustration of the lead-through of the connection cable is an example. The location of the grommet may vary depending on the seat and model. We assume no guarantee for a seat heater is already installed. If the seat heating worked before the seat conversion, it will also work after the seat conversion.
詳細を見る
このシートカバー「AIR」は、シート周囲の空気循環を一定に保ちます。走行中はメッシュ生地を通して空気が循環し、シートを効果的に冷却します。また、炎天下の駐車時にシートが過熱するのを軽減します。マジックテープで簡単にシートに取り付けることができます。3Dメッシュ生地製。 前席シート用と後席用シートのセットです。
詳細を見る





