シートヒーターの後付け

全モデル

詳細を見る

Retrofitting a seat heater for single seat

品番 sitz.heiz
特別価格 EUR 216,75 通常 EUR 255.00
税込, 送料別
USD: $238.25GBP: £181.16AUD: A$354.99JPY: ¥38,113
納期: しばらくお待ちください。

Retrofitting a seat heater for seat bench (only rider)

品番 sb.heizF
特別価格 EUR 216,75 通常 EUR 255.00
税込, 送料別
USD: $238.25GBP: £181.16AUD: A$354.99JPY: ¥38,113
納期: しばらくお待ちください。

Retrofitting a seat heater for seat bench (rider and passenger)

品番 sb.heizFS
EUR 484,00
税込, 送料別
USD: $532.01GBP: £404.53AUD: A$792.70JPY: ¥85,107
納期: しばらくお待ちください。

通関手数料が発生するため、EU以外の国からのシートの発送をお受けすることができません。大変申し訳ありませんが、EU域外からシートを発送するお客様には、「シートヒーターの後付け」サービスをご提供することができません。

Retrofitting a 2-stage (15W/30W) seat heater for seats that do not have seat heating as standard.
Possible either only in the rider's position or in the rider's and passenger's position.

The original seat cover must be removed for installation, which is why it must not be glued to the foam core! Check whether the cover can be lifted off the foam core! To do this, pinch the cover between your thumb and forefinger and try to lift it (see figure 4). Attention: If the cover is glued, the seat heating can only be retrofitted in combination with a seat conversion (see seat conversion (one-piece seat) / seat conversion (two-piece seat))!

After installing a seat heater, the cable for the power supply is led out under the seat shell (approx. 20 cm long with plug connection). You will receive an approx. 120cm long connection cable with a two-stage, round built-in toggle switch (diameter approx. 20mm) for each heated seat position. The connection to the electrical system of your motorcycle should be carried out by a specialist workshop, knowledge of motorcycle electronics is required! A circuit diagram is included.

The seat heater will be installed on your seat - you have to send it in!
The change takes about 2-3 weeks.

The illustration of the lead-through of the connection cable is an example. The location of the grommet may vary depending on the seat and model.

商品についての質問

レビュー


未レビューの商品はありません


製品安全情報



関連・おすすめ商品

New cover for seat
New cover for seat

通関手数料のため、EU 以外の国からの座席の提出は受け付けられません。 したがって、EU 圏外から座席を送付する必要がある場合は、残念ながら「座席の新しいカバー」というサービスを提供できません。. If your seat cover is damaged or worn, we can equip your seat with a new cover. For example, if you have your rider's seat reupholstered by us, it can also make sense for visual reasons to have the passenger seat covered with the same artificial leather so that the overall result looks harmonious. By default, we use non-slip black synthetic leather and black stitching for the seat cover (other colors are also possible). Several colors or different types of synthetic leather, lettering and other customizations are possible at an additional cost. The original seat cover must be removed, which is why it must not be glued to the foam core! Check whether the cover can be lifted off the foam core! To do this, pinch the cover between your thumb and forefinger and try to lift it (see figure 2). Attention: If the cover is glued, a new seat cover can only be realized as part of a seat conversion (see seat conversion (one-piece seat) / seat conversion (two-piece seat))! Your seat will be changed - it must be sent in! The change takes about 2 weeks. The illustrations of the service "new cover for seat" are examples! Whether a seam has to be worked in or not depends on the condition of the seat. Our upholsterer will make the new cover similar to the original cover as far as possible.

EUR 126,00EUR 140.00

税込, 送料別

詳細を見る
フロントシート、リアシートの改良
フロントシート、リアシートの改良

通関手数料が発生するため、EU 以外の国からのシートの発送をお受けすることができません。大変申し訳ありませんが、EU外からシートを発送するお客様には、「シートの改良」サービスをご提供することができません。 The seat is modified according to your individual needs. Based on your information on our seat data sheet, we can adapt the seat to you in terms of hardness, contour and height. Among other things, a groove (deepened middle of the seat) is possible, which noticeably relieves the coccyx if there are problems with it. The seat conversion is possible with different height options: 1: like the original seat 2: lower (up to -25mm) 3: higher (up to +25mm) BMW R1250GS is also available with factory seat heating. This results in the following restrictions: Lowering the seat (-25 mm) is not possible due to the heating integrated in the seat. When making the seat higher (+25mm), the additional foam reduces the heat output. Many seats are also offered by BMW in a low version - these cannot be lowered further. By default we use non-slip black synthetic leather and black stitching for the seat conversion (other colors are also possible). Several colors or different types of imitation leather, lettering and other customizations are possible at an additional cost. Example modifications: Examples of seat modifications Please fill out the seat change form and send it to us. Please wait for our confirmation before sending the seat to us. In this way you can avoid unnecessary shipping costs if a conversion cannot be carried out as desired. Your data sheet: Please fill in and send to us! Your seat will be modified - it must be sent in! The modification will take about 2 weeks. Each image of the service "seat conversion" can of course only be an example! Seams are not always possible with very soft seats, for example! Our upholsterer can only decide whether a seam needs to be incorporated or not after he has received the information on your form. If there is no seat heating as standard, an accessory seat heating can be retrofitted with the seat conversion. The retrofit includes the installation of a 2-stage (15W/30W) seat heater and all connection parts required for operation. After installing a seat heater, the cable for the power supply is led out under the seat shell (approx. 20 cm long with plug connection). You will receive an approx. 120cm long connection cable with a two-stage, round built-in toggle switch (diameter approx. 20mm) for each heated seat position. The connection to the electrical system of your motorcycle should be carried out by a specialist workshop, knowledge of motorcycle electronics is required! A circuit diagram is included. The illustration of the lead-through of the connection cable is an example. The location of the grommet may vary depending on the seat and model. We assume no guarantee for a seat heater is already installed. If the seat heating worked before the seat conversion, it will also work after the seat conversion.

EUR 229,00EUR 240.00

税込, 送料別

詳細を見る
10 mmローダウン用ゴムバッファー
10 mmローダウン用ゴムバッファー

BMW R1250GS モデル

純正シート下のラバーバッファーを交換することで、シート高を約10mm下げることができます。ラバーバッファーは工具を使わず簡単に交換できます。ラバーバッファーの穴はオフセットされています。シートを下げるには、薄い側を上向きにして取り付けてください(画像2参照)。

EUR 14,90

税込, 送料別

詳細を見る